Efficient Networks EEE 802.11b/g Wireless USB 2.0 Adapter Manual do Utilizador

802.11b+g Wireless USB Adapter User’s Manual www.unicomlink.comUNIDOC111904 pn: WEP-45020G

- 7 - Verify To verify if the device exists in your computer and is enabled, go to Start  Settings  Control Panel  System ( Hardware)  De

- 8 - NETWORK CONNECTION Once the device driver is well installed, a network setting described in the following should be also established. In Window

- 9 - 3. For making your computer visible on the network, enable the File and Print Sharing. 4. Click the Identification tab. Make up a name that

5. Click the Access Control tab. Make sure that “Share-level access control” is selected. If connecting to a Netware server, share level can be

In Windows 2000/XP 1. (In Windows 2000) Go to Start Settings  Control Panel  Network and Dial-up Connections  Local Area Connection  Properties

2. Make sure that all the required components are installed. 3. If any components are missing, click on the Install… button to select the

- 13 - IP Address Note: When assigning IP Addresses to the computers on the network, remember to have the IP address for each computer set on the sam

- 14 - Configuration Utility After the Wireless adapter has been successfully installed, users can use the included Configuration Utility to set thei

- 15 - Note: There will be two modes – Station and Access Point for you to switch, you can select the mode you need from the pull-down menu.

- 16 - Station Select Station mode, and you will see the following figure. Channel Shows the selected channel that is currently in use. (There are 1

REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have e

Tx Rate Click the down arrow ▼ to select the Tx Rate from Auto, 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54 Mbps, you can select up to 54 Mbps. Encry

Tx Frame The quantities for the wireless network card transmit. (Frame: The unit of packet) Rx Frame The quantities for the wireless network card rec

- 19 - Network Type The infrastructure is intended for the connection between wireless network cards and an Access Point. With the wireless adapter,

- 20 - Default Key ID：You can set your default key ID at #1~#4. Key Format ：Select Hexadecimal if you are using hexadecimal numbers (0-9, or A-F).

Certificate ： Please query your network manager about the certificate, select the same certificate as the certification server. Load You may select

- 22 - Advanced Setting User Interface Language Select English or Traditional Chinese. Power Consumption Setting Continuous Access Mode (CAM

- 23 - Country Roaming World Mode This function is only enabled and effective with 802.11d standard. User Select Enable this function to select the

- 24 - Access Point To set your 802.11g Wireless LAN USB Adapter as an Access Point (AP). In access point mode, the 802.11g Wireless LAN USB Adapter

- 25 - Network Adapter You can select the network adapter from the pull-down menu, it shows the device itself（the 802.11g Wireless LAN USB Adapter）

Tx Frame The quantities for the wireless network card transmit. (Frame: The unit of packet) Rx Frame The quantities for the wireless networ

Table of Contents INTRODUCTION ...1 FEATURES ...

- 27 - Channel Shows the selected channel that is currently in use. (There are 14 channels available, depending on the country.) Mode Select Mixed

- 28 - Authentication Mode Select the Authentication mode from the pull-down menu, there are two modes for you to choose, Open System and Shared Key

MAC Address Filter Click Setting and you will see the following figure. You can select the Filter Type from the pull-down menu. Disable：Select to d

- 30 - Appendix Soft AP Configuration Setup Requirement: To bridge your wired and wireless network using 802.11b+g Wireless LAN USB Adapter, the fo

- 31 - 1. Select the Access Point mode, and you will see the following figure 2. Click the More Setting… button and the following figure will appea

- 32 - 4. If the network connected to the wired LAN card has a DHCP server, you just need to configure the wireless station as a DHCP client (selec

- 1 - INTRODUCTION The 802.11b+g Wireless LAN USB Adapter is designed for a USB type A port of a laptop or desktop computer for creating a wireless w

- 2 - SOFTWARE INSTALLATION Step 1: Install the Driver & Utility For Windows 98, 2000, ME and XP users Caution! Do not insert the wireless L

3. When the Welcome screen appears, click Next to continue. 4. The installation program will start running automatically. Follow the on-screen

- 4 -

- 5 - HARDWARE INSTALLATION Windows 2000/XP Note: Before you install the device to your computer, make sure you have installed the driver and utili

- 6 - 4. Click Continue Anyway → Finish to complete the hardware installation. Windows 2000 Insert the USB adapter into the USB port of y